Depth to rock in Melbourne siltstone: checking before you dig

In much of Melbourne, the rock under a block is Silurian age siltstone, widely called Melbourne Mudstone or the Melbourne Formation. Across the central and eastern suburbs it usually sits beneath a few metres of residual clay, so a footing or a basement wall often meets weathered rock within the first few metres of excavation. In the volcanic western suburbs and the river and creek flats, the picture changes completely, and rock can be tens of metres down or not reached at all. Knowing roughly how deep rock is, and what kind, changes how you price footings, excavation and a basement before anyone drills a hole.

This matters to builders and engineers for a plain reason. Rock that is close to the surface can carry heavy loads and resist buoyancy, but it is slow and expensive to dig. Rock that is deep means piles, tension anchors or a longer design discussion. A desktop check narrows the range before the drill rig arrives.

What is Melbourne Mudstone

Melbourne Mudstone is the common name for the Silurian age bedrock beneath much of the Melbourne region. It is a monotonous, interbedded sequence of siltstone, which dominates, with mudstone and thin sandstone horizons (McDonald et al. 2013). The siltstone is made largely of angular quartz grains with occasional feldspar, laid down by density flows in a deep marine setting (Australian Geomechanics 2015).

As a rock it is soft to weak. Published uniaxial compressive strength figures for the siltstone sit at the low end of the rock scale, around 1 to a few MPa for the weaker material (Australian Geomechanics 2015). It is also folded and fractured, which matters for excavation faces and for how water moves through it. The point for a builder is that this is rock you can usually rip and bolt rather than blast, but it is still rock, and it is slower and costlier to remove than clay.

How deep is rock under a Melbourne block

There is no single number, because the cover over the rock varies with where in the city you are.

Across the central and eastern suburbs, the typical profile is a few metres of residual clay over weathered siltstone that grows stronger with depth. On one Melbourne CBD site, investigations found roughly three to five metres of residual clay above weathered siltstone, with the rock extremely weathered near the top and improving further down (McDonald et al. 2013). That upper-few-metres pattern is common across the folded Silurian country.

Near the Yarra, Maribyrnong and Moonee Ponds systems, Quaternary river and delta sediments bury the siltstone far deeper. At North Melbourne, an embankment near Moonee Ponds Creek sits on Yarra Delta sediments over the Silurian siltstone and sandstone, including the soft, low-strength Coode Island Silt near the surface (Australian Geomechanics 2016). On some river-flat sites the depth to siltstone can exceed 50 metres, and in design it has been treated as effectively out of reach rather than a bearing stratum (Australian Geomechanics 2019).

In the volcanic western and northern suburbs, a different rock sits on top. Basalt of the Older Volcanics can overlie a very stiff clay known as the Werribee Formation, which in turn overlies the Silurian siltstone. One western-region profile recorded basalt and Werribee Formation above Silurian siltstone first met below about 37 metres (Australian Geomechanics 2019). If you are working on basaltic ground, the reactive clay from that basalt is a separate design issue worth reading up on in a basaltic clay worked example.

Setting What usually sits above the rock Typical depth to Silurian siltstone
Central and eastern suburbs A few metres of residual clay Weathered rock within the first several metres
River and creek flats (Yarra, Maribyrnong) Quaternary alluvium and soft silts Often tens of metres, can exceed 50 m
Volcanic west and north Older Volcanics basalt over Werribee Formation clay Can be below 30 to 40 m

Why depth to rock changes the footing and excavation cost

Shallow, strong rock is good news for bearing and poor news for digging. Weathered siltstone that improves with depth can support spread footings and heavy loads, and it can resist groundwater uplift under a basement raft without large tension piles (Australian Geomechanics 2019). The trade-off is excavation effort: fractured, folded rock is slower to remove, and a deep basement face in it needs careful support, which is why wall movement and stability are the focus of CBD basement case studies (McDonald et al. 2013).

Deep rock reverses the problem. Where siltstone is far down and the near-surface material is soft alluvium, footings carry into weaker ground and piles may need to reach a competent layer, which lengthens the piling programme and the budget.

For a house, depth to rock also feeds the broader excavation question. If you are costing a cut-and-fill or a basement, read it alongside the general guidance on checking depth to bedrock before you price excavation.

What a desktop check can tell you, and where it stops

A desktop report assembles the published geology for an address: the mapped unit, whether it is Silurian siltstone, Older Volcanics basalt or Quaternary alluvium, and any nearby groundwater bore logs that record what was met and at what depth. Groundwater is part of the picture, because in the CBD siltstone it has been found around 11 to 12 metres below the surface on some sites (McDonald et al. 2013), which affects basement waterproofing and uplift.

What the desktop cannot do is tell you the exact rock level, weathering or strength under one lot. Rock depth and quality in the Melbourne Formation vary over short distances because the rock is folded. Only boreholes, cored to rock, give the design numbers. The desktop sets the expectation and scopes how many holes and how deep. It is not engineering advice for a specific footing.

Common questions

How deep is rock in Melbourne? It depends on where in the city the block is. In the central and eastern suburbs, weathered Silurian siltstone (Melbourne Mudstone) often sits beneath only a few metres of residual clay. On the Yarra and Maribyrnong flats, rock can be tens of metres down, and in the volcanic west it can sit under basalt and stiff clay at 30 metres or more.

What is Melbourne Mudstone? Melbourne Mudstone is the common name for the Silurian age Melbourne Formation, the bedrock under much of Melbourne. It is interbedded siltstone, mudstone and thin sandstone, with siltstone dominant. It is a soft to weak rock, folded and fractured, and it generally gets stronger with depth as weathering reduces.

Do I need a borehole if rock is shallow? Yes. A desktop report can tell you the likely rock type and rough depth from published geology and nearby bore logs, but only boreholes cored to rock confirm the actual level, weathering and strength under your lot. The folded Melbourne Formation varies over short distances, so field investigation is still required for footing or basement design.

To see the mapped geology, nearby bore records and the likely ground profile for a Melbourne address before you commit to a field investigation, generate a desktop report for the address or see a sample report.

LayeredGeo compiles geology, soils, groundwater and site data into an automated geotechnical desktop report for any address in Queensland, New South Wales, Victoria and South Australia.

Sources

  • Peter McDonald , Michael Broise and David Chong (2013). Deep Basements In Melbourne Siltstone. Australian Geomechanics, 2013 Sydney Symposium (2013). geomechanics.org.au
  • Australian Geomechanics Society (2015). Proceedings of the 12th Australia New Zealand Geomechanics Conference. Australian Geomechanics, 12th Australia and New Zealand Conference on Geomechanics (Feb 2015). geomechanics.org.au
  • Australian Geomechanics Society (2019). Proceedings of the 13th Australia New Zealand Conference on Geomechanics. Australian Geomechanics, 13th Australia and New Zealand Conference on Geomechanics (2019). geomechanics.org.au
  • Australian Geomechanics Society (2016). 11th Young Geotechnical Professional Conference Proceedings. Australian Geomechanics, 11th Young Geotechnical Professionals Conference (Oct 2016). geomechanics.org.au

Common questions

How deep is rock in Melbourne?

It depends on where in the city the block is. In the central and eastern suburbs, weathered Silurian siltstone (Melbourne Mudstone) often sits beneath only a few metres of residual clay. On the Yarra and Maribyrnong flats, rock can be tens of metres down, and in the volcanic west it can sit under basalt and stiff clay at 30 metres or more.

What is Melbourne Mudstone?

Melbourne Mudstone is the common name for the Silurian age Melbourne Formation, the bedrock under much of Melbourne. It is interbedded siltstone, mudstone and thin sandstone, with siltstone dominant. It is a soft to weak rock, folded and fractured, and it generally gets stronger with depth as weathering reduces.

Do I need a borehole if rock is shallow?

Yes. A desktop report can tell you the likely rock type and rough depth from published geology and nearby bore logs, but only boreholes cored to rock confirm the actual level, weathering and strength under your lot. The folded Melbourne Formation varies over short distances, so field investigation is still required for footing or basement design.

LayeredGeo Georeport

Get this data for your site

A geotechnical desktop study for any QLD, NSW, VIC or SA address - geology, soils, groundwater, contours and nearby bore logs in one PDF, delivered in minutes for $119.

Get your site report → See a sample report

About this article. Published by LayeredGeo and written from the published research cited in the Sources section above. It is general information about how property and ground conditions are assessed in Australia, not engineering, planning, legal or financial advice, and it is not specific to any property. Check anything that matters against the source dataset or a suitably qualified professional before you rely on it. If you spot something wrong, tell us at hello@layeredgeo.com.au and we will fix it.

← All articles